This repair kit allows you to fix cracks, damages or holes on the aero parts made of FRP, jet skis, boats or surfboards. You can use the package as a mixing tray. The high-intensity “Glass Mat" is used for the glass fiber, the main part of FRP.
| Name of product | FRP Repair Trial Set |
|---|---|
| JAN code | 4975759092087 |
| Content | 430g Putty : 145ml Hardener : 4ml Glass Mat × 1 (300×200mm) Powder : 50g Measuring Cup × 1 Spoon × 1 Spatula × 1 |
| Ingredients and materials | Main agent: Synthetic resin Curing agent: Organic peroxide |
| Storage and disposal methods | STORE SEALED BELOW 40℃, OUT OF DIRECT SUNLIGHT. AVOID HUMIDITY, FREEZING, AND WETTING. USE/RELEASE CONTENTS COMPLETELY BEFORE DISPOSING ACCORDING TO LOCAL REGULATIONS. |
How to use the product
(Preparation)
1. Remove any chips or splinters from the area being repaired with a cutter. After rubbing on both sides and around the area to make it smooth, wash off any residue or dirt.
2. Cover over the hole or crack with the masking tape.
3. Cut the glass mat into 2 sheets as needed.
(Filling a hole with resin)
1. Mix both agents well. And pour the resin into the hole and apply it on a bit wider area than the bigger sheet.
2. Put the bigger sheet on it and press it with the included spatula.
3. Apply the resin in the same process and put the smaller sheet on it. After press it with the included spatula, apply the resin over it again.
* After the resin hardens completely, take off the masking tape.
(Making the surface smooth with the putty)
1. Mix the agent well with the powder.
2. Apply the putty with the included spatula by flattening out it.
3. After it hardens completely, polish on it with sandpaper (150-grit> 320-grit) until there is no gap between repaired part and around it.
4. Make the surface smooth with the 600-grit sandpaper.
5. Finish up with Atelier 99 Body Paint.
1. Remove any chips or splinters from the area being repaired with a cutter. After rubbing on both sides and around the area to make it smooth, wash off any residue or dirt.
2. Cover over the hole or crack with the masking tape.
3. Cut the glass mat into 2 sheets as needed.
(Filling a hole with resin)
1. Mix both agents well. And pour the resin into the hole and apply it on a bit wider area than the bigger sheet.
2. Put the bigger sheet on it and press it with the included spatula.
3. Apply the resin in the same process and put the smaller sheet on it. After press it with the included spatula, apply the resin over it again.
* After the resin hardens completely, take off the masking tape.
(Making the surface smooth with the putty)
1. Mix the agent well with the powder.
2. Apply the putty with the included spatula by flattening out it.
3. After it hardens completely, polish on it with sandpaper (150-grit> 320-grit) until there is no gap between repaired part and around it.
4. Make the surface smooth with the 600-grit sandpaper.
5. Finish up with Atelier 99 Body Paint.
-
- USE ONLY FOR INTENDED PURPOSE.
USE ONLY IN WELL-VENTILATED AREAS.
WASH HANDS WELL WITH SOAP AFTER USE.
THIS PRODUCT CONTAINS FIBERGLASS, DO NOT TOUCH DIRECTLY. AS SKIN IRRITATION MAY OCCUR, PLEASE WEAR PROTECTIVE GLOVES.
DO NOT MIX WITH OTHER PRODUCTS OR MATERIALS.
PUTTY MIXED ONCE CANNOT BE REUSED. MIX ONLY WHAT YOU NEED. DISCARD REMAINING MIXED PRODUCT.
SUITABLE FOR USE BETWEEN 10°C AND 30°C. THIS PUTTY CURES QUICKLY AT HIGH TEMPERATURES, AND SLOWLY AT LOW TEMPERATURES. IT IS DIFFICULT TO CURE AT TEMPERATURES OF LESS THAN 5°CC, DO NOT USE.
- USE ONLY FOR INTENDED PURPOSE.
-
DO NOT EAT OR DRINK. HARMFUL IF SWALLOWED OR INHALED.
DO NOT INHALE, TOUCH OR ALLOW CONTACT WITH SKIN. RISK OF POISONING, IRRITATION AND SKIN RASH.
CAUTION: CURING AGENT IS HIGHLY TOXIC.
FLAMMABLE. KEEP AWAY FROM HEAT AND FIRE.
CAUTION: CURING AGENT GENERATES HEAT DURING CURING PROCESS. BE CAREFUL OF BURNS. USE WITH CARE.
KEEP OUT OF REACH OF CHILDREN AND VULNERABLE PEOPLE.