This kit is for "DIY beginner" who challenge to repair body dent. Includes "Body Filler" and "Lacquer Putty" as a kit. Tube type can store left over.
| Name of product | Body Filler & Lacquer Putty Trial Kit |
|---|---|
| JAN code | 4975759092308 |
| Content | 【Body Filler】 Main Agent: 150g Hardener: 7g 【Lacquer Putty】 26g |
| Ingredients and materials | 【Thickening putty】 Main agents: synthetic resins, pigments, organic solvents Curing agents: organic peroxides, organic solvents 【Usus-supti Putty】 Synthetic resins, pigments, organic solvents |
| Storage and disposal methods | STORE SEALED BELOW 40℃, OUT OF DIRECT SUNLIGHT. AVOID HUMIDITY, FREEZING, AND WETTING. USE/RELEASE CONTENTS COMPLETELY BEFORE DISPOSING ACCORDING TO LOCAL REGULATIONS. |
How to use the product
【Body Filler】
1. Rub on the area being repaired with the 150-grit sandpaper.
* Remove oily comportment by Silicone off.
2. Take main agent and hardener as 100:2 and mix well by attached spatula.
3. Apply the mixed putty on the desired area with the included spatula to fill in the scratch.
* Putty gets hardened approx 1 hour (20℃).
* Beware of applying too much at once more than 10mm, it causes crack or peeling.
4. After hardened, poling with sand paper 320→600 grits to adjust the shape.
* Rub with wet condition.
【Lacquer Putty】
1. Put the moderate amount of putty onto attached spatula.
* Work quickly otherwise this putty dries immediately.
2. Put the putty thinly and evenly as if it embed scratch and pin hole.
* Apply within 1mm at once, otherwise inner area doesn't dry.
* Putty gets hardened approx 1 hour (20℃).
3. After hardened, poling with sand paper 320→600 grits to adjust the shape. After that, finish up with sandpaper and Atelier 99 Body Paint.
1. Rub on the area being repaired with the 150-grit sandpaper.
* Remove oily comportment by Silicone off.
2. Take main agent and hardener as 100:2 and mix well by attached spatula.
3. Apply the mixed putty on the desired area with the included spatula to fill in the scratch.
* Putty gets hardened approx 1 hour (20℃).
* Beware of applying too much at once more than 10mm, it causes crack or peeling.
4. After hardened, poling with sand paper 320→600 grits to adjust the shape.
* Rub with wet condition.
【Lacquer Putty】
1. Put the moderate amount of putty onto attached spatula.
* Work quickly otherwise this putty dries immediately.
2. Put the putty thinly and evenly as if it embed scratch and pin hole.
* Apply within 1mm at once, otherwise inner area doesn't dry.
* Putty gets hardened approx 1 hour (20℃).
3. After hardened, poling with sand paper 320→600 grits to adjust the shape. After that, finish up with sandpaper and Atelier 99 Body Paint.
-
- USE ONLY FOR INTENDED PURPOSE.
USE ONLY IN WELL-VENTILATED AREAS.
WASH HANDS WELL WITH SOAP AFTER USE. DO NOT MIX WITH OTHER PRODUCTS OR MATERIALS. (THICK PUTTY)
PUTTY MIXED ONCE CANNOT BE REUSED. MIX ONLY WHAT YOU NEED. DISCARD REMAINING MIXED PRODUCT. (THICK PUTTY)
SUITABLE FOR USE BETWEEN 10°C AND 30°C. THIS PUTTY CURES QUICKLY AT HIGH TEMPERATURES, AND SLOWLY AT LOW TEMPERATURES. IT IS DIFFICULT TO CURE AT TEMPERATURES OF LESS THAN 5°CC, DO NOT USE. DEPENDING ON THE CONDITION OF THE CAR AND PAINT, RESULTS MAY VARY. RISK OF SCRATCHES/PEELING.
OPEN CAREFULLY, CONTENTS MAY COME OUT UNEXPECTEDLY. (THIN PUTTY)
- USE ONLY FOR INTENDED PURPOSE.
-
DO NOT EAT OR DRINK. HARMFUL IF SWALLOWED OR INHALED. DO NOT INHALE, TOUCH OR ALLOW CONTACT WITH SKIN. RISK OF POISONING, IRRITATION AND SKIN RASH.
CAUTION: CURING AGENT IS HIGHLY TOXIC.
AS SKIN IRRITATION MAY OCCUR, PLEASE WEAR PROTECTIVE GLOVES.
FLAMMABLE. KEEP AWAY FROM HEAT AND FIRE.
Curing agent heating, because there is a risk of burning explosively due to impact, be careful when using.
KEEP OUT OF REACH OF CHILDREN AND VULNERABLE PEOPLE.